Victory! Yesterday, I successfully applied the greek trim after my first failed attempt. My process was very similar, but a few key differences that made ALL the difference.
Heres how I did it.
First, I got out my cutting mat, metal ruler with cork backing (for anti-slip), and my xacto knife. I used basically the same measurements as my first attempt, with a few tweaks to accommodate the new shams. For a standard sham (mine are these), I used {16} 4", {8} 6", {2} 7", and {2}14" pieces of ribbon (diagram a few images down). My ribbon is 7/8" pewter grosgrain ribbon from Joanns, Wal-Mart has the same though.
I started by cutting the end at a 45, the cutting mat made this easy because I could line the ruler from corner to corner of the 1" square. For the edge to be clean and straight, it helps to hold tightly on the ruler and change your blade frequently (I have a pack of 100 I purchased on Amazon since buying a few at a time is so expensive and I use them a lot)
Then measure your desired length for the straight edge. Again, the cutting mat helps with this too, since each square is 1". My measurements above are from the tip of the 45 to the straight edge. and repeat this for all of your pieces.
I love putting my hiccups on here because you help me figure them out! A big thank you to Jani for giving me the idea to burn the ends!
I found that using a lighter gives the most control since you want it to be as even as possible. I did use a candle (to save my finger) for a lot of the ends. Since that gets covered, it isnt as important if it is straight.
Then I centered it on the pillow (adding up the entire width and height and subtracting the respective difference from the ends). Its really easy to get the spacing off, I recommend laying it all out and double checking your measurements before adhering.
* pink outline shows original ribbon and how the edges meet.
I started with the long 14" piece on the bottom (45 pointed left and straight edge right) and worked right overlapping the 45s on the straight edge. After testing two samples of adhesive that I had (to make sure that it didnt show through) I used one roll of 3/4" heat n bond super. Last time I used heat n bond regular and had issues with it showing through, but Im thinking that its because I had to iron so many corners that it got too liquid and bled through. The important thing is not to iron too long. I had my iron on fairly hot, pressed for a few seconds and then if it felt pretty secure, I would move to the next. Its hard to tell until it is cool if it is really adhered, so I went back at the end and touched up any spots that were a little loose. For the touch up spots, I flipped the sham over and ironed from the back. The extra layer of fabric helped prevent it from getting too hot and bleeding through. Make sense? :)
I tried to make the heat n bond as close to the edge as possible, but after I was finished, I put little pieces in the corners that needed a little more and then ironed. and make sure that your iron is
dry (I had just dumped out the water in mine).
and thats it! This was so much easier to get precise then folding every corner and ironing!!
It took about 30 minutes to cut and seal the trim per pillow and about an hour to hour and a half to lay it out and iron it down. So about 1.5 to 2 hours per pillow.
Also, for those who dont want to cut at a 45, cutting straight with scissors would also work well and give a very similar look!
Price breakdown:
Ribbon - pewter grosgrain 7/8" x2 = $4.00
Heat n Bond 3/4" Super = $2
Total = $6
So is it worth the time or would you rather buy? I think its worth it, but that may be because I enjoying doing this kinda stuff :)
Also, I havent forgotten about the trim on the draperies for the bedroom ... just trying to find something that doesnt cost more than the draperies themselves ... looks like I may be adjusting my idea!
--
Update: Also see my latest tutorial on how to apply greek key trim with one continuous piece of ribbon, here
